 |
|
|
|
|
Am29LV2562M Product Overview
512 Megabit (16 M x 32-Bit/32 M x 16-Bit)
MirrorBit™ 3.0 Volt-only,
Uniform Sector Flash Memory with Versatile I/0™ Control
General Description
The Am29LV2562M of two 256 Mbit, 3.0 volt single power supply flash memory
devices and is organized as 16,777,216 doublewords or 33,554,432 words.
The device has a 32-bit wide data bus that can also function as an 16-bit
wide data bus by using the WORD# input. The device can be programmed either
in the host system or in standard EPROM programmers. An access time of 120
ns is available. Note that each access time has a specific operating voltage
range (VCC) as specified in the Product Selector Guide and the Ordering
Information sections. The device is offered in an 80-ball Fortified BGA
package.
Each device has separate chip enable (CE#), write enable (WE#) and output
enable (OE#) controls. Each device requires only a single 3.0 volt power
supply for both read and write functions. In addition to a VCC input, a
high-voltage accelerated program (WP#/ACC) input provides shorter programming
times through increased current. This feature is intended to facilitate
factory throughput during system production, but may also be used in the
field if desired.
The device is entirely command set compatible with the JEDEC single-power-supply
Flash standard. Commands are written to the device using standard microprocessor
write timing. Write cycles also internally latch addresses and data needed
for the programming and erase operations.
The sector erase architecture allows memory sectors to be erased and reprogrammed
without affecting the data contents of other sectors. The device is fully
erased when shipped from the factory.
Device programming and erasure are initiated through command sequences.
Once a program or erase operation has begun, the host system need only poll
the DQ7 and DQ15 (Data# Polling) or DQ6 and DQ14 (toggle) status bits or
monitor the Ready/Busy# (RY/BY#) outputs to determine whether the operation
is complete. To facilitate programming, an Unlock Bypass mode reduces command
sequence overhead by requiring only two write cycles to program data instead
of four.
The VersatileI/O™ (VIO) control allows the host system to set the
voltage levels that the device generates.
Distinctive Characteristics
Architectural Advantages
- Single power supply operation
- 3 volt read, erase, and program operations
- VersatileI/O™ control
- Device generates data output voltages and tolerates data input
voltages on the CE# and DQ inputs/outputs as determined by the voltage
on the V10 pin; operates from 1.65 to 3.6 V
- Manufactured on 0.23 µm MirrorBit™ process technology
- SecSi™ (Secured Silicon) Sector region
- 128-doubleword/256-word sector for permanent, secure identification
through an 8-doubleword/16-word random Electronic Serial Number,
accessible through a command sequence
- May be programmed and locked at the factory or by the customer
- Flexible sector architecture
- Five hundred twelve 32 Kdoubleword (64 Kword) sectors
- Compatibility with JEDEC standards
- Provides pinout and software compatibility for single-power supply Flash, and superior inadvertent write protection
- 100,000 erase cycles per sector
- 20-year data retention at 125°C
Return to Top
Performance Characteristics
- High performance
- 120 ns access time
- 30 ns page read times
- 0.5 s typical sector erase time
- 15 µs typical write buffer doubleword programming time: 16-doubleword/32-word
write buffer reduces overall programming time for multiple-word
updates
- 4-doubleword/8-word page read buffer
- 16-doubleword/32-word write buffer
- Low power consumption (typical values at 3.0 V, 5 MHz
- 26 mA typical active read current
- 100 mA typical erase/program current
- 2 µA typical standby mode current
- Package Options
Return to Top
Software Features
- Program Suspend & Resume: read other sectors before programming operation is completed
- Erase Suspend & Resume: read/program other sectors before an erase operation is completed
- Data# polling & toggle bits provide status
- Unlock Bypass Program command reduces overall multiple-word or byte programming time
- CFI (Common Flash Interface) compliant: allows host system to identify and accommodate multiple flash devices
Return to Top
Hardware Features
- Sector Group Protection: hardware-level method of preventing write operations within a sector group
- Temporary Sector Unprotect: VID -level method of changing code in locked sectors
- WP#/ACC input accelerates programming time (when high voltage is applied) for greater throughput during system production. Protects first or last sector regardless of sector protection settings
- Hardware reset input (RESET#) resets device
- Ready/Busy# output (RY/BY#) detects program or erase cycle completion
Return to Top
|
|
|
|
|
|
